pricing5
pricing4
pricing3
pricing2
pricing1


This Series basic design from Meyer Hydraulics has served as the general aviation industry standard for over 55 years. The A600 Series and its predecessors are being used by professional service technicians around the world providing confident lifting of airplanes and helicopters weighing up to 8000 lbs. (3629kg) with the security and features one should demand in an aircraft jack. Even after the additional TriTask features have been added, the A600 Series still continues to be surprisingly affordable.


A: INNER SLIDE TUBE - The 2.375" (60mm) diameter powder-coated Tube forms the foundation of the TriTask Aircraft Jack System. The zigzag pattern of .5" (13mm) safety lock-out holes are vertically spaced 1" (25mm). The
Tube's top has a 1" (25mm) diameter threaded hole designed to receive an AT-JPRn Jacking Point Receiver, a Top-of-the-Jack Load Cell or an AT-EBnnn Extension Bar.
B: POSITIVE SAFETY LOCK - Spring-loaded safety pin "pops" into the Inner Slide Tube and rests on top of the Jack's frame to prevent the accidental lowering of the aircraft.
C: STEADY KNOBS remove any side movement of the Inner Slide Tube after the airplane or helicopter is raised to the desired height.
D: TWO ACCESSORY TUBES are provided to allow the operator to put in accessories or tools for on-board storage if desired.
E: MILLED FLAT AREA ON EACH LEG increases surface contact to help prevent any hanger floor surface damage.
F: LOW HEIGHT LEG DESIGN provides maximum gear door clearance, with one of the four sections completely free of any protrusions. The four legs insure excellent stability with its 26.875" (68.3cm) square footprint. When the A634 Jack is using the AJL-ZA Extension Leg Set, the square footprint is 37.625" (95.6cm). Contact Meyer Hydraulics if your gear door clearance is less than 1.562" (40mm) from the center of the aircraft's jacking point.
G: ANTI-SNAG ROUND FRAME TUBE Has a 2.875" (73mm) diameter.
H: THREE 3" (76mm) SPRING LOADED CASTERS allow easy transporting of the Jack around the hanger without the need for the steel legs to scuff across the floor.
I: OPTIONAL ALW-10 LEVELING WASHER SET is a perfect solution when it's necessary to shim the A600 Series Aircraft Jack legs because the hanger floor isn't completely flat or level. The ALW-10 isn't to be used with the A300 or A700 Series Aircraft Jacks.


TriTask Jack Low Height
(Tube only)
Low w/AT-JPR1* Hydraulic Stroke High Height
(Tube only)
High w/AT-JPR1*
A622 w/AT62222* 22.312" (56.7cm) 22.5" (57.2cm) 15" (38.1cm) 37.312" (94.8cm) 37.5" (95.3cm)
A622 w/AT62234 34.312" (87.2cm) 34.5" (87.6cm) 15" (38.1cm) 49.312" (125.3cm) 49.5" (125.7cm)
A627 w/AT62727* 27.312" (69.4cm) 27.5" (69.9cm) 20" (50.8cm) 47.312" (120.2cm) 47.5" (120.7cm)
A634 w/AT63434*
(w/AJL-ZA Legs)
34.312" (87.2cm)
44.312" (112.6cm)
34.5" (87.6cm)
44.5" (113cm)
25" (63.5cm)
25" (63.5cm)
59.312" (150.7cm)
69.312" (176.1cm)
59.5" (151.1cm)
69.5" (176.5cm)
A634 w/AT63448
(w/AJL-ZA Legs)
48.312" (122.7cm)
58.312" (148.1cm)
48.5" (123.2cm)
58.5" (148.6cm)
25" (63.5cm)
25" (63.5cm)
73.312" (186.2cm)
83.312" (211.6cm)
73.5" (186.7cm)
83.5" (212.1cm)


*Comes standard with that TriTask Jack







Eurocopter 120 Helicopter


Cessna 210

Cessna Twin Aircraft

The three Aircraft Jack Sets below have been designed to provide professinal technicians with the selection of equipment that best matches their own needs. Each Set has its own unique combination of aircraft jacks and accessories to lift the maximum number of different types of airplanes and helicopters weighing up to 8000 lbs. (3629kg) for the least amount of capital investment.

A600JS-A TriTask Basic Aircraft Jack Set includes:
  2) A622 Jacks w/AT62222's and AT-JPR1's
  2) A634 Jacks w/AT63434's and AT-JPR1's
  1) AJL-ZB Extension Leg Set (8 legs)
  1) AT-EBZA Extension Bar Set
  2) AT62234 Inner Slide Tubes
  2) AT63448 Inner Slide Tubes
  1) ATS Aircraft Tailstand

A600JS-B TriTask Deluxe Aircraft Jack Set includes:
  1) A600JS-A TriTask Basic Aircraft Jack Set
  1) A622 Jack w/AT62222 and AT-JPR1
  1) ALW-10 Leveling Washer Set
  1) AT-EBZB Extension Bar Set
  1) AT62234 Inner Slide Tube
A600JS-C TriTask Premium Aircraft Jack Set includes:
  1) A600JS-A TriTask Basic Aircraft Jack Set
  2) A627 Jacks w/AT62727's and AT-JPR1's
  1) ALW-10 Leveling Washer Set
  1) AT-EBZB Extension Bar Set
  1) ATS-AA72 Extended Inner Slide Tube


The most advanced and versatile aircraft lifting system for
maintenance professionals servicing airplanes and helicopters
weighing up to 32000 lbs. (14517kg)
image1
image1
The Inner Slide Tubes
The new TRITASK Aircraft Jacks with their powder-coated
Inner Slide Tubes form the "anchor" of the new TriTask System.
leftThe top of the A600 and A700 Series Inner Slide Tubes are designed to receive an AT-JPRn, AT-EBnnn or a top-of-the-jack aircraft weighing Load Cell.
leftThe Inner Slide Tubes for the A500 Series have a built-in 1.25" (32mm) round Jacking Point receiving socket machined into the top of its protruding anchoring stud.The AT500-CA Conversion Adapter can be mounted on the anchoring stud, which will then allow the A500 Series Inner Slide Tubes to function the same as the A600 and A700 Series Inner Slide Tubes.
left
Top portion of A600 and
A700 Series Inner Slide Tube
left
Top portion of A500 Series
Inner Slide Tube
image1
left


AT-JPR1 in an A600 or A700 Series Aircraft Jack Inner Slide Tube
left

AT-JPR2 in an
AT500-CA
Conversion
Adapter
for the
A500 Series
AT-JPRn Jacking Point Receivers
Made of solid steel and powder-coated with a long-lasting yellow finish for easy spotting, these JPR Receivers have been designed to be put into the top of an A600 or A700 Series Aircraft Jack's Inner Slide Tube, an AT-EBnnn Extension Bar or the AT500-CA Conversion Adapter for the A500 Series. The AT-JPR1 is a 1.5" x .187" (38x5mm) pad with a .875" (22mm) round Jacking Point receiving socket. The AT-JPR2 is a little larger with a 1.75" x .375" (44x10mm) pad with a 1.25" (32mm) round receiving socket. Both have a 1" x 1" (25.25mm) round stem.
image1
left

AT500-CA Conversion Adapter, Mounted on top of an A500 Inner Slide Tube
left

Mounting Load Cell in AT500-CA Conversion
Adapter
Mounted to an
A500 Inner Slide Tube
AT500-CA Conversion Adapter
This optional 2.25" (57mm) round steel
powder-coated Adapter only connects to the A500 Series Inner Slide Tubes and adds .875" (22mm) to the height of the Jack. After securing the Adapter to the Inner Slide Tube's protruding anchoring stud, an AT-JPRn, AT-EBnnn or a top-of-the-jack aircraft weighing Load Cell can be quickly put into the top of the Conversion Adapter.
Mounting the AT500-CA Conversion Adapter to an A500 Inner Slide Tube
image1
left

AT-EBnnn screwed
into an AT500-CA
Conversion
Adapter
on top of
an A500 Series
Inner Slide Tube
left

AT-EBnnn with an
AT-JPRn in an A600 or A700 Aircraft Jack's Inner Slide Tube
left
AT-EB015 thru AT-EB125 Extension Bars Extends the height of the TriTask Jack so technicians can get close to the airplane or helicopter without wasting valuable hydraulic lifting stroke.
AT-EBnnn Extension Bars
Twelve (12) optional 1.75" (44mm) solid steel
powder-coated Extension Bars of various lengths screw into the top of an A600 or A700 Aircraft Jack's Inner Slide Tube or into the AT500-CA Conversion Adapter used on the A500 Series. They extend the height of the Jack 1.5" to 12.5" (38 to 318mm) in 1" (25mm) increments. Both of the AT-JPRn Jacking Point Receivers or a top-of-the-jack aircraft weighing Load Cell can quickly be put into the top non-threaded hole of an
AT-EBnnn Extension Bar. The AT-EBnnn's cannot be used on the A755C and A760A Aircraft Jacks.
image1
image1
Built-in Ability to use a
Top-of-the-jack Helicopter and
Airplane Weighing Load Cell
A Load Cell with the standard 1" x 1" (25x25mm) round
stem can be quickly put into the top of an A600 or
A700 Series Aircraft Jack's Inner Slide Tube, an
AT-EBnnn Extension Bar or the top of an AT500-CA
Conversion Adapter used on the A500 Series.

Meyer Hydraulics does not make or distribute aircraft
weighing Load Cells or Scales. These are readily available
from other sources, such as one of our Select Distributors
or Jackson Aircraft Weighing Scales.
left
A500 Inner Slide Tube with AT500-CA Conversion Adapter, AT-EB025 Extension Bar and Load Cell
left
Mounting Load Cell in
an A600 or A700 Series
Inner Slide Tube